dentiform

dentiform

1. For increases rubber dentiform bring 's intension and service life, Our factory increase wrap cloth on original basis, Can many use about in a.

为了增加橡胶齿形带的强度及使用寿命，我厂在原基础上增加了包布，可多用一年左右。

2. Divided into dentiform gasket,flat gasket,compoundd graphite dentiform gasket.

分为齿形垫片、平垫、复合石墨型齿形垫。

3. Keywords Sectional Intermeshing Twin-screw Reactor;Dentiform Element;Tine Number;Flow Field Analysis;PP;

分段啮合双螺杆反应器;齿型元件;齿型数;流场分析;聚丙烯;

4. The method named the cold precision forging of controllable floating die can effectively improve the dentiform fill and reduce the forming load.

在此基础上，提出了浮动凹模浮动模式可调的齿轮精锻法，这种新方法对于改善齿形填充和降低成形载荷都是行之有效的。

5. Three problems on solving magnetic field between pointed dentiform poles in literatures are discussed.

对文献报道的求解磁场过程中存在的3个问题进行探讨。

6. compare with the screw, gear and dentiform strap wheel by hiberarchy analysis, choose the dentiform strap wheel drive the feed device finally.

并且利用层次分析法，对丝杠螺母、齿轮齿条、同步带轮三种传动方式进行比较排序，最终确定以同步带方式为喂线装置的往复运动。

7. The bed surface is divided to back board and seat board.The dentiform bar lifting framework is operated by hand wheel.Back board can be fold up and down to suit various body positions.

床面分背板，座板，通过手轮操作齿箱条升降结构，背板可以上折、下折，以适合各种体位的需要。

8. Design of a worm dentiform thickness measurement equipment with digital and multifarious

数显式多种模数蜗杆齿厚检测装置设计

9. Check the dentiform belt-driven suppositoties slot is rotating, troubleshooting, press the screen indicates that the kangyouwei key to recovery.

检查齿型皮带传动栓槽轴是否可转动，排除故障后，按下荧幕指示复归键即可恢复运转。

10. The foils are approved by National Food &Health Standard.It is packaged by colour box with dentiform blade and easy to pick up.

此产品符合国家食品卫生标准，并由带切割锯条的彩盒包装，美观大方。

11. Because of the flexibility of enveloping method than dentiform normal method, three new screws are designed by enveloping method with flow field analysis.

由于包络法比齿型法线法应用简便，因此我们采用包络法设计了三种新型螺杆元件，并对其分别进行了流场分析。

12. Comparative Analysis of Dentiform Error by Scatter Measuring and Seriate Measuring

离散与连续测量齿形误差的分析比较

13. Dentiform transformation method of iris inner edge location

虹膜内边缘定位的齿形变换方法

14. lobes 9, dentiform.

裂片9，齿状。

15. The numerical results showed that dentiform element had strong diffluent and distributivity-mixed ability, but its dispersity mixing ability was weak.

计算结果表明：齿型元件具有较强的分流能力和分布性混合能力，但分散性混合能力较弱。

16. Optimize the shape of dentiform using CVM as the optimize algorithm.The result were satisfied.

选取约束变尺度法作为优化算法，对斜齿轮进行了齿廓优化，得到了满意的结果。

17. Via replacing different dentiform milling flake and adjusting strike technics.It will be suited for various requiremnts of striking pulp.

通过调换不同齿形的磨片和调整打浆工艺，可以适应各种浆料的打浆要求。

18. Dentiform belt wear, up and down both sides of the belt gap is too large or not.

齿型皮带上下磨损严重，两边皮带间隙太大或不一样。

19. dentiform to significant wear belt so that it is inconsistent with the high and low, and the pressure gauge pressure is low, the effect is easy to transfer the normal paerboard.

齿型皮带出现明显磨损，使其高低不一致，以及压力表压力不足时，都会容易影响纸板的正常输送。

20. Dentiform informention belt damaged, do not match.

齿型皮带已磨损，高低不一致。

21. Experiment and research on cleaning moment strengthening for rotation plastic dentiform strip

齿型自转塑料纽带清洗力矩强化实验研究

22. Some Problems in Solving Method of Magnetic Field Between Dentiform poles

齿尖磁极相对的磁场求解中几个问题的探讨

23. dentiform error

齿形误差

24. dentiform crystals.

齿状的结晶