flange
flange
1. Flange bolts may be tightened by conventional ring spanners on class 150# for utility piping systems.
150号等级的公用管道系统上的法兰螺栓可以使用通用梅花双头板手来紧固。
2. In 2002, our corporation won the competitive bidding of the anchor flange for West-East Gas Pipeline Project.
2002年我公司在西气东输管道工程锚固法兰的竞标中。
3. MAXON's A Style Synchro flow control valve bodies are designed to meet ANSI flange specifications.
MAXON的A型同步流量控制阀阀体的设计满足ANSI的法兰规格要求。
4. A customized dipstick can be added to breathers with the flange style adapter.
一个订制液位计可以被添加到呼吸与法兰作风适配器。
5. A cast iron flange with three adjustable screws will conveniently hold a crown thermocouple.
一个铸铁轮缘有三个可调的螺钉,便于控制炉顶热电偶的位置.
6. Pressure gauges in our standard range with triangular bezel or front mounting flange.
三角企口沟缘或前固定法兰的标准压力表。
7. Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.
上紧叶片弹簧加压机直到衬套凸缘的底部扎实地扺住叶片弹簧的孔眼。
8. Slightly press the flange of the square panel without a crater to obtain jointless effect.
不带坑方向折边,稍加轻压,便可达到紧凑无缝的效果。
9. Do not rely on the flange bolting to support the valve or connecting pipeline.
不能依赖法兰螺栓来支撑阀门或连接管道。
10. Do not use Permatex or RTV silicone on the metal flange surface.
不要在金属法兰表面使用Permatex或RTV硅树脂。
11. And a variety of boiler flange pair of sliding flange, you can adjust the burner into the boiler.
与各种锅炉法兰配对的滑动法兰，可以调整燃烧器伸入锅炉的位置。
12. Speciality manufasctukre: Hexagon Nuts Domed Cap Nuts, Nylon locking Nuts, Flange Nuts, Outet Sawtootn gasket.
专业供应六角螺帽、盖形螺帽、尼龙锁紧螺帽、法兰面螺帽、外锯齿垫圈。
13. Two outer rings each with a central integral flange and two loose flange ring; one intermediate rings.
两个外圈分别带一个中心整体式法兰和两个松配合法兰环;一个隔圈。
14. The standard contrast table for Chinese and foreign Fittings, flange and bar material.
中外锻制管件、法兰、棒材材料标准对照表。
15. Nominal length exceed 3m, shall be with fixing Flange for reinforcement.
中心距超过3米,需加固法兰或耳攀。
16. The bottom flange and the diaphragms must be selected carefully to match the product.
为与产品匹配，需仔细选择底部边缘和隔膜。
17. Retighten all flange bolts in a star pattern in order to extrude rubber sleeve flange material.
为了将橡胶套管法兰挤出来，需要按照星形模式重新紧固所有法兰螺栓。
18. R indicates the distance from fitting face of flange to axle shoulder.
为凸缘配合面至轴伸肩的距离。
19. Primary flange rating is Class 600 or lower.
主法兰等级为600级或以下。
20. Mainly products: flange, valves, gemel, marine Hardware, builder's finish hardware.
主要产品有法兰，阀门，铰链，船用五金件，流体设备配件、建筑五金、车辆配件等。
21. Maximum thickness of the products is 70mm on the web and 80mm on the flange.
产品的最大厚度:腹板70mm,翼板80mm。
22. Here is a blind flange at the clean water piping from oily water separator to sea.
从油水分离器出口通海管路上有盲板。
23. Optimized flange contours provide full spoke elbow support, increasing spoke life.
优化法兰轮廓全力支持以肘，增加发言的生活。
24. Permits all nozzles to be used with the flange style 1"(2.54 cm) OD nozzle extension tube.
使所有喷嘴都可以与外径为1英寸(2.54厘米)的法兰式喷嘴延长管一起使用。
25. We are manufacturing mainly in: Fasteners: Hex Bolts, Hex Nuts,Flange bolt and Nuts,Carriage Bol...
供应标准及非标准螺栓，螺母，紧固件（图）
26. Allow the sleeve flange to return to its original position.
允许套管法兰回到它的初始位置。
27. The shape of the intake is like SAE high-pressure flange.
入口形状为相当于SAE标准压力的法兰。
28. Engages in the production of die mould material,large forging,and chrome steel flange.
公司从一九九六年建立以来，从各大钢厂吸取技术，引进各大型锻打设备及炼钢技术。
29. Produced products with all kinds of mold, screw, Shaft, flange and various mechanical parts.
公司生产产品有各类模具、丝杠、轴类、法兰及各种机械部件。
30. Additional features include: flange mounted interchangeable rewind shafts and a pneumatic lay-on system.
其它附加功能包括：法兰安装可互换倒带轴和气动布局的系统。
31. Provides deadend service without the need for a flange on the downstream side.
具有截断功能，不需要在出口端加装法兰。
32. One integral flange and one loose flange ring on the inner ring.
内圈带一个整体式法兰和一个松配合法兰圈。
33. The other bead of the tire is removed from over the same side of the rim flange in a similar manner.
再用类似的方法拆卸另一边的轮缘。
34. Lug body available with ISO flange dimensions and metric bolt hole threads.
凸耳式阀体符合ISO法兰尺寸和公制螺栓孔螺纹。
35. Lug body available with ISO flange dimensions and metric bolt hole threads. For dead-end service use lug style (rated 200 PSI for this service).
凸耳阀体也可配置ISO法兰尺寸和公制螺栓孔螺纹。用于终端位置可采用凸耳结构（此时额定压力为200PSI）。
36. The manufacturability of a fixing cover with flange seal was analyzed.
分析了带凸缘密封固定盖的工艺性,介绍了级进模总体设计结构和排样设计。
37. The analysis results indicated that the H_2S in the LPG caused sulfide stress corrosion cracking (SSCC) of the flange.
分析结果表明,法兰断裂是由液化气中的H2S所引起的应力腐蚀开裂。
38. The analysis results indicated that the H2S in the LPG caused sulfide stress corrosion cracking (SSCC) of the flange.
分析结果表明，法兰断裂是由液化气中的H2S所引起的应力腐蚀并裂。
39. To create the flange brand is our pursuing.
创法兰品牌是我们的追求。
40. FEM has been used to simulate and analyze the high pressure rubber forming process of part with flange bending.
利用有限元技术,对凸翻边钣金零件的高压橡皮成形过程进行模拟分析。
41. The front hub features a unique 85mm wide flange placement which increases lateral wheel stiffness by nearly 20%.
前端枢纽，具有独特的85毫米宽凸缘安置车轮的侧向刚度增加了近20%。
42. Shifting linkage that makes contact with the spool flange to activate the reversal.
卷筒盘接触来触发换向的移动键。
43. Press the flange and replace the side sealing ring.
压紧法兰（均匀用力）更换侧密封圈。
44. See 'Technical Data"section for end flange dimensions and drilling templates.
参阅《工程技术资料》章节,了解连接端口法兰尺寸和钻孔模板。
45. We are Wuxi Huaan Flange Co.,Ltd. Located at Jiangyin City, China, and we are one of the largest fla...
发布者：何海斌所在地：江苏无锡市行业：冶金矿产职位：外销员工作年限：五年以上
46. Another , flange supplying the various pipeline accessory, if elbow etc.
另供应各种管道配件，如弯头、法兰等。
47. Export the valve,flange and fittings.
另常年出口阀门及配件。
48. The flange should only be removed when the sleeve has reached its final position.
只有当套管已到达其最终位置时,才能将法兰去掉。
49. Only one set of flange studs is needed.
只需要一套法兰柱头螺栓。
50. It canbe used to weave filling or weave with other materialsEven direct using as pump, valve and flange sealing.
可制做各种密封编织填料或与其他材料混合编织，或直接用于泵、阀、法兰的密封。
51. We can provide flange connection of various standards.
可提供各种标准的法兰连接。
52. Dimension list of pressure grade corresponding flange of flexible rubber joint, connecting dimension is dimension.
可曲挠橡胶接头压力等级对应配套法兰尺寸表,连接尺寸为国标尺寸。
53. A tire tool or flat stock can be used to pry one part of the bead up over the rim flange (start near the valve stem ).
可用轮胎工具或扁平的撬棒把轮缘的一端从轮辋辋圈上撬起。
54. The flange cut that consequently its sub implements very easily in clean is in (namely the brim) observe.
因而它的胶层很轻易在洁具的翻边切割处(即边缘)观察到。
55. Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference.
在传动轴和传动轴轴轭、或小齿轮轴轭上作标记，作安装的参考标志。
56. An electrified wire can be strung along the outer edges of this flange.
在外缘引上一条通了电的电线。
57. An O-ring located in nacelle flange is applied between the grease channels in nacelle and bearing.
在机舱润滑油脂通道和轴承之间有O形圈，O形圈位于机舱法兰上。
58. Whenever flange bolts are tightened the torquing sequence must be done in a star pattern (See Figure 5).
在紧固法兰螺栓时，必须按照星形模式顺序（参阅图5）来进行螺栓紧固。
59. Small rectangular backup bars were used to fabricate the web-bottom flange connection.
在腹板与下翼缘的施焊中使用小矩形挡板。
60. Grease flange threads of body to inhibit rust or corrosion.
在阀门法兰螺纹处涂上油脂，防止生锈或腐蚀。
61. Tighten all bolts evenly as for a standard flange assembly.
均匀地紧固所有螺栓，形成标准的法兰总成。
62. Gland ? two piece gland bushing/packing flange is self-aligning to prevent stem damage for cocked gland.
填料压盖-两件式填料压盖衬套/填料法兰能够自动校准，以防止由于填料压盖翘起造成阀杆损坏。
63. It has feet arrangement and flange arrangement.
备有地脚安装和法兰安装形式。
64. One integral flange on the outer ring and one loose flange ring.
外圈带一个整体式法兰和一个松配合法兰圈。
65. Outer ring with integral central flange and two loose flange rings.
外圈带整体式中心法兰和两个松配合法兰圈。
66. A big multifunction flange mouth. A man can stretch a hand in it.
多功能大型法兰口,手可伸入。
67. Grip the wire at the flange of the spool without touching the wire as shown in photo 6.2.1.2.
夹断线尾在靠近瓷嘴的位置,紧握线盘的边缘注意不要碰到金线(如图6.2.1.2所示)把线盘从机器上卸下来
68. The inlet side of the sleeve is appropriately marked with an inlet tag on the inlet flange O.D.
套管的进口端要在法兰外径上采用一个进口标签加以适当的标注。
69. Unless specified otherwise, the reduction unit is supplied with the flange in pos. D referred to position B3.
如无特别声明,减速机的法兰将设在D的位置上,这安排是根据B3的形式.
70. When used with a "raised face" flange, there will be a gap between the faces on the outer flange diameters.
如果使用“凸面”法兰，则在外法兰直径表面之间将会有间隙。
71. As the gasket extrudes from the body, it may push the rubber flange away slightly from the cast body.
如果垫圈从阀体内挤出，则可能会将橡胶法兰从铸造阀体上轻微推出。
72. If the flange does not extend far enough, there will be insufficient saliva retained, and again, loss of retention.
如果基托伸展不够，则唾液粘结面积不足，同样丧失固位。
73. Turn the locking bolt so that it is fixed on the bake cover or the flange plate.
安装后必须将锁紧螺母锁紧在电机后端盖或法兰盘上。
74. Turn the hollow bolt so that it is fixed on the bake cover or the flange plate.
安装后必须旋出空心螺栓锁紧在电机后端盖或法兰盘上。
75. Shanxi Dingxiang Chang Xing Steel Flange Co., Ltd.
定襄县昌兴钢材法兰有限公司。
76. A circular flange or rim, as in a ring, into which a gem is set.
宝石座环形法蓝盘或轮圈，用以在戒指上镶嵌宝石
77. A groove or flange designed to hold a beveled edge, as of a watch crystal or a gem.
宝石座用来固定斜面的沟槽，如钟表或宝石的
78. To low drawing in flange part,the blank holder can be used as punch,and the effect is good.
对于凸缘部位的浅拉深,采用压边圈兼作浅拉深凸模的作用,取得较好的效果。
79. For flange size backflow preventers installed vertically (flow down), a fabricated air gap is recommended.
对于垂直安装的法兰通径防回流阀，则建议采用预制气隙。
80. Align mark on front universal joint, or CV joint, to the mark on the axle pinion yoke, or flange.
将前万向节或CV万向节上的标志与车轴小齿轮轴轭或凸缘上的标志对准。
