piercer
piercer
1. ADJUSTMENT OF THE MAIN DRIVE REDUCER ECCENTRIC SLEEVE OF BOTH ACCU ROLL MILL AND PIERCER
Accu Roll轧管机和穿孔机主传动减速机偏心套调整
2. Design of Bearing Retainer Automatic Piercer of Control with PLC
PLC控制侧窗自动冲孔模设计
3. Keywords three roll cross rolling;piercer;roll shape;rolling effect;secondary piercing;
三辊斜轧;穿孔机;辊形;辗轧效应;二次穿孔;
4. three roll piercer
三辊穿孔机
5. Keywords Three-high piercer;Shell quality;Rolling failure;
三辊穿孔机;毛管质量;轧制故障;
6. New Technology of Rolling Block to Avoid in Three-roll Piercer
三辊轧管过程避免轧卡的新工艺
7. The paper offered relatively formula for piercer's designing and fabrication in the future.
为今后设计、制造二辊斜轧穿孔机提供了比较简明合理的参考计算方法。
8. Keywords Two-high rotary piercer;Pierced shell;W.T.uneveness;Roll taper;
二辊斜轧穿孔机;毛管;壁厚不均;轧辊锥角;
9. two-roll piercer
二辊穿孔机
10. Comparison of Two Roll Cone Shaped Roll Piercer with Three Roll Barrel Type Piercer
二辊锥形辊穿孔与三辊鼓形辊穿孔对比分析
11. The article describes a solution to eliminate spiral W.T. uneveness of the shell from the rotary piercer by means of modifying the roll taper and presents the calculating formula for the roll taper.
介绍了用改进穿孔机轧辊锥角解决毛管产生螺旋性壁厚不均的方法，给出了确定轧辊锥角的计算公式。
12. he introduction involves major aspects of the rotary piercer integrated plug such as the integration type, materials used, operational features as well as the effect thereby on the product quality.
介绍了组合顶头的组合方式、使用材料、性能特征及对钢管质量的影响等。
13. This article presents a built up sleeve method to change the collar of cone type piercer,including the calculation of the shrink fit of the roller ring that the roll surface is conic.
介绍用镶套的方法更换锥形穿孔机轧辊辊环，对外表面为锥面的轧辊辊环的过盈联接进行了计算和设计，提出了一种对过盈联结中包容件外表面不是圆柱面时的实用计算方法。
14. Effective methods in aspects of tool design and adjusting parameters of the cross-roll piercer are put forward for improving the wall-thickness uniformity of the shell pierced.
从工具设计和轧机调整参数的角度，探讨了改善毛管壁厚均匀性的行之有效的途径和方法。
15. Discussion on the Piercing Principle of Cone Roll Piercer and Its Application
关于锥形辊穿孔机的穿孔原理及应用问题的讨论
16. Discussion of Inflaence by Cone Type Piercer Roll Speed on Shell Lamination Defect
关于锥形辊穿孔机轧辊转速对毛管分层缺陷影响的讨论
17. Keywords piercer;dies;graduation;automation;retainer;
冲孔机;模具;分度;自动;保持架;
18. Moreover,the mathe matic model of the piercer rolling pressure is analyzed by the writer.
分析了穿孔轧制压力的数学模型。
19. Approach on Characteristics of Cone-type Piercer
国产锥形穿孔机的特点分析
20. During the operation course of the plug pipe mill line,shell waiting might occur due to the fact that the working cycles of the piercer and the plug mill are not properly matched to each other.
在自动轧管生产中，因穿孔和轧管节奏不匹配会引起毛管传搁。
21. The mighty Mt Cook, known as the "Cloud Piercer", is the highest peak in Australasia at 3755m.
巍峨的库克山,被誉为“云霄之钻”,是澳大拉西亚地区最高的山峰,高3755米。
22. 2. The mighty Mt Cook, known as the "Cloud Piercer", is the highest peak in Australasia at 3755m.
巍峨的库克山,被誉为“云霄之钻”,是澳大拉西亚地区最高的山峰,高3755米。收藏指正
23. It has been proven by trial commercial production that With the piercer plug designed by means of the said new method,much higher radial wall thi...
工业性试验结果表明，新设计的穿孔顶头能显著提高毛管的横向壁厚精度。
24. Conventional length of functional section is the distance from needlepoint to the upper port of gradual deflating piercer, whose common notation is the distance from needlepoint to lower port.
常规工作段长度是从针尖至渐缩锥上口的距离，普通写法是到下口的距离。
25. can piercer
开罐头刀
26. It is pointed out that like the barrel type piercer process,the control of the cone type piercer roll speed is also very important.
指出了锥形辊穿孔机也要和桶形辊穿孔机一样,要重视对穿孔机轧辊转速的控制。
27. Also discussed are relevant issues concerning use of the equation of piercer roll opening to determine the said conical angle.
探讨了利用斜轧穿孔机轧辊开度方程来选择顶头平整段锥角的有关问题。
28. One way to enhance the working life of piercer point by means of Re-Al alloying was offered and its feasibility was proved in this paper.
提出了利用稀土铝合金化提高顶头使用寿命的措施,并对该措施的可行性进行了论证。
29. Abstract The FEM simulation software of DEFORM was used to simulate the temperature distribution of plug for Diese piercer during cross rolling.
摘要 应用DEFORM三维有限元数值模拟软件对狄舍尔穿孔机热轧穿孔过程中的顶头进行了温度场数值模拟，通过模拟和实测分析了顶头开裂、粘钢、塌鼻等失效原因。
30. INFLUENCE OF TOOL DESIGN AND ADJUSTMENT OF CROSS-ROLL PIERCER ON WALL-THICKNESS UNIFORMITY OF THE SHELL PIERCED
斜轧穿孔工具和轧机调整对毛管壁厚均匀性影响
31. The computation of the roll opening is the basis of tool design and parameters adjustment of skew rolling piercer.
斜轧穿孔机轧辊开度计算是轧机工具设计和调整参数计算的基础。
32. Analysis on the Roller Cone Angle Design of Smooth Rolling of Skew Rolling Piercer
斜轧穿孔机轧辊辗轧锥角的设计分析
33. Design and Reform of the Roll Box of Mannesmann Piercer
曼氏穿孔机轧辊箱改造设计
34. Carpenter's Alloy KOBAYASHI Adjustable Piercer
木工合金小林可调开孔器
35. Methods proposed in this paper are not only suitable for Mannessmann piercer but also for Diesher piercer, rotary-rolling piercer and modern VIP.
本文提出的方法不仅适合于普通曼氏穿孔机，同样也适合于狄舍尔穿孔机、菌式穿孔机以及现代VIP。
36. Based on the result of relevant research, technical requirements to core structure of the CC round and the relationship between the said structure and the profile of the piercer plug are put forward.
根据研究结果提出了对连铸圆管坯芯部状态的要求，并指出管坯芯部状态与穿孔机顶头形状的关系。
37. wave piercer
波冲头
38. jet piercer
火力钻孔机
39. jet piercer drilling
火力钻眼
40. DEMETRIUS So should the murdered look;and so should I, Pierc'd through the heart with your stern cruelty;
狄米特律斯：被杀者的脸色应该是这样的，你的残酷已经洞穿我的心，因此我应该有那样的脸色；
41. diescher piercer
狄舍尔穿孔机
42. Relevant operation practice of the millleads to a conclusion that the three-high piercer is fully capable of producing shells with high W.T. accuracy and good surface quality.
生产实践证明，三辊穿孔机完全能够穿制出壁厚精度高、表面质量好的毛管。
43. disk piercer
盘式穿孔机
44. Keywords Piercer;Modification;Characteristic curve equation;Plug bar;Critical Pressure;
穿孔台;改进;曲线方程;顶杆;临界压力;
45. Keywords Piercer;Compound plug;Manufacture process;
穿孔机;复合顶头;研制工艺;
46. Keywords Piercer;Cradle fixing;Angle adjustment;Improvement;
穿孔机;转鼓固定;角度调整;改进;
47. The Three-dimensional Parameterized Design of Piercer Guide Board Series
穿孔机导板系列的三维参数化设计
48. DEVELOPMENT OF PIERCER GUIDE DISC LUBRICATION TECHNIQUE
穿孔机导盘润滑技术的开发
49. TECHNICAL DEVELOPMENT OF WATER-SOLUBLE LUBRICANTS FOR PIERCER GUIDE DISC
穿孔机导盘用水溶性润滑剂的开发
50. Automatic Position Control System of Piercer
穿孔机的自动位置控制系统
51. piercer roll
穿孔机轧辊
52. Being used for controlling and adjusting of roll angle, piercer roll cradle is considerably responsible for uneveness of the pierced shell wall thickness in terms of controlling level thereof.
穿孔机轧辊转鼓用于控制和调整轧辊角度，它的控制水平对穿孔毛管壁厚不均度有很大影响。
53. Piercer plug
穿孔顶头
54. Keywords Piercer plug Oxide film Properties;
穿孔顶头;氧化膜;性质;
55. ear lobe piercer
耳垂穿孔器
56. ear piercer
耳穿孔器
57. turf piercer
草地疏松透气器 草地更新器
58. Analysis on Samples of Clogged Horizontal Cast Billets Pierced by Conical Piercer
菌式穿孔机穿轧水平连铸坯时轧卡试样的分析
59. At present, Model CTP-600-20 jet piercer with chambering diameter of 600 mm and more is a largest one in Commonwealth of Independent States, which equipped with two compressors with capacity of 32 m~3/min each.
装有两台32m~3/min空压机、能扩孔至600mm甚至更大直径的CTP-600-20型火钻,是目前独联体最大型的火力扩孔钻机。
60. The piercing principle of 2-roll cross-rolling piercer and its application range are discussed.
论述了二辊斜轧锥形辊穿孔机的穿孔原理及其应用范围。
61. Four types of piercer plug initial f ailures relating to its structural dimensions are discussed,the causes are analyzed,and countermeasures put f orward.
论述了四种与穿孔顶头结构尺寸有关的顶头早期失效形式及其特征,分析了产生的原因,提出了相应的改进措施。
62. It can be used not only for pass design and off line analysis but also for guiding in the adjustment of piercer.
该系统不仅可用于斜轧穿孔工具设计和离线分析，还可用于指导穿孔机操作。
63. Automatic piercer of bearing retainer
轴承保持架自动冲孔机
64. Mannesmann piercer
辊式穿轧机 曼内斯曼式穿孔机
65. Keywords Continuously cast billet for pipe-making;New type piercer;Pipe-rolling process facilities;Heat treatment;On-line inspection;
连铸管坯;新型穿孔机;轧管工艺设备;热处理;在线检测;
66. The basic process of three-dimensional parameterized design for the piercer guide board series has been described in this article as well as its necessity and superiority with CAD.
针对某型集装箱吊具导板机构故障频发、使用寿命短和维修成本高的弊端,在充分吸收其他吊具导板机构优点的基础上,对其进行了设计改造。
67. iron piercer
铁锥子
68. Application of cone-type piercer technology on producing heavy wall thickness steel tube
锥形穿孔技术在中厚壁钢管生产中的应用
69. Keywords cone type piercer;roller;built up sleeve;shrink fit;
锥形穿孔机;轧辊;镶套;过盈配合;
70. Cone type piercer
锥形辊穿孔机
71. Keywords Cone Type Piercer Driving spindles Double supporting Feed angle;
锥形辊穿孔机;传动轴;双支承;辗轧角;
72. Keywords Cone roll piercer;Cavity;Forming mechanism;Application;
锥形辊穿孔机;孔腔;形成机理;应用;
73. Keywords Cone type piercer;Roll speed;Toe angle;Torsional deformation;Lamination defect;Dis-cussion;
锥形辊穿孔机;轧辊转速;辗轧角;扭转变形;分层缺陷;讨论;
74. Description of Piercer Mill and the Research of the Premium Arrangement of Driving Spindles for the Cone Type Piercer Mill
锥形辊穿孔机综述及其轧辊传动轴布置方式初探
75. The major quality defect as occurring in the cone type piercer process with highdeforming steel and alloy steel is the lamination.
难变形钢和合金管坯在锥形辊穿孔机上穿孔,毛管的主要质量问题也是分层缺陷;
