runout

runout

1. A candidate needs more than 50% of the vote to avoid the runout of the a run-off election.

候选人需要超过半数以上的投票来避免在竞选中被淘汰。

2. Profile controls everything that total runout does as well as size if the size dimension is made BASIC.

全跳动除了尺寸，对形状，方向和位置都给出了公差规范要求。

3. As regards the axial runout it is recommended that values given in the table are being used.

关于轴向跳动,建议使用“相关部件精度”一节中表3给出的数值。

4. The results of temperature, stress and microstructure were calculated about three kinds of cooling pattern on the runout table.

分析表明，采用稀疏冷却方式能提高厚度方向上的冷却均匀性；

5. "Not grabbing the quickdraw in the middle of that scary runout" is achievable, whereas "sending the route this try" is not.

因此，请找些既有挑战性又有能力完成的路线。例如在爬5.9的时候可能让你觉得爬起来最顺畅。

6. In service, fatigue cracking initiated at the plating runout led to lug fracture.

在实际使用中，在镀层的过渡段发生的疲劳裂纹会导致接耳断裂。

7. In a hot strip mill,runout table cooling is the most critical factor to determine final mechanical properties of product it makes.It is ...

在热连轧的过程模拟中,层流冷却是决定产品最终力学性能的最关键过程。

8. There is oil aplenty of other sorts (tar sands, liquefied coal and so on), so the stuff is unlikely to runout for a long time yet.

大量的石油是由其他方式存在的（沥青砂，液化煤等等），所以，油价不太可能长期脱缰。

9. For me, the cerebrally intense highball problem replaced the runout, which the drill destroyed a decade ago.

对我来说，这些令人紧张刺激的活动让我远离了退缩，不再象十年前那样。

10. We have runout of toilet paper.

我们把卫生纸用完了。

11. The struggling Ferraris are just seventh and ninth on the grid, while neither Renault graduated into the top-ten runout.

挣扎法拉利只是第七和第九位发车，而雷诺既不毕业进入前十名跳动.

12. The failure mechanisms and the loading capacity of stiffened composite panels with stiffener runout are studied.

摘要研究了复合材料加筋板筋条斜削区的失效过程并预测了结构的承载能力。

13. Check front wheel and tire assembly for radial runout.

检查前车轮及车胎组件之径向偏置。

14. Each roll needs to have a certain degree of manufacturing accuracy, principally roll of coaxality, runout, UN-roundness and roll a tapered bore taper.

每个版辊都必要有必定的创作发明精量，次要指版辊的同轴量、径向跳不静、不圆量以及版辊锥孔的锥量。

15. The mechanism of impacts of cutter runout on the pratical cutting radius,chip form and chip thickness was studied and analyzed.

研究了径向跳动对刀齿的实际切削半径、切屑形状以及切屑厚度的影响机理。

16. The result indicates that the load for delamination initiation is increased with the increase of the runout length.

结果表明，增加筋条斜削区长度可以延缓脱层的起始。

17. The maximum runout between the thread and the locating face is 0,005 mm for nuts up to and including size 26.

螺纹同定位面之间的最大跳动为0,005mm为螺母尺寸代号于等于26。

18. A long runout equates to a long fall.

这个距离越大，脱落的距离越长。

19. The temperature and stress-strain field of steel plate runout table cooling are simulated using thermo-elasto-plastic finite element method.

针对钢板冷却发生翘曲变形的问题,利用热弹塑性有限元法对中厚板冷却过程的温度场及应力应变场进行数值模拟。