toolholder

toolholder

1. Keywords HSK toolholder;contact pressure;connection performance;

HSK刀柄;接触应力;联结性能;

2. KM Toolholder

KM刀柄

3. Keywords KM Toolholder;Finite-element Analysis;Taper Contact;

KM刀柄;有限元分析;锥面接触;

4. The results can be used as basis and instruction for application of HSK toolholder and optimization of geometry parameters.

为HSK刀柄的实际应用及几何参数优化提供一定的依据及指导。

5. This paper presents a linear servo toolholder system to cut workpieces with non-circular crosssections.

介绍用于非圆截面零件车削的刀架系统。

6. offset toolholder

偏置刀架

7. Keywords toolholder;connection performance;high rotary speed;

关键词7/24刀柄;联结特性;高速旋转;

8. Toolholder selection is governed by tool design and intended function.

刀具把的选择取决于刀具设计和需要的功能。

9. Tool system is the structure constitutes a tool of the system, which mainly refers to tool material, tool and toolholder.

刀具系统是指构成刀具的系统结构，其中主要是指刀具材料、刀具结构和刀柄。

10. toolholder bit

刀夹 刀头

11. toolholder support

刀夹支架

12. toolholder slide

刀架滑台

13. toolholder and tooling system

刀柄及工具系统

14. Shown here are a quick-change tooling system based on a standard square-shank lathe toolholder (right), as well as a cross-section of a coated PCBN insert (left).

图片说明: 此处显示的是一个快速更换刀具系统，它建立在一个标准的方形支柱车床刀架(右)上，还显示了一个PCBN涂层刀片的横截面(左)。

15. Then introduce how to choice machine, machine tool, toolholder, balance tool, tool safety, cutting parameter and cooling.4 Grouping clamp is one of the most important in the grouping technology.

在本文中从机床选取、刀具选取、刀具夹紧方式的选取、刀具动平衡、刀具安全性、切削用量的选取以及冷却技术等方面进行介绍。

16. accelerating toolholder

增速刀柄

17. The toolholder is used for outer slotting and the tool bar for inner slotting and for slotting the keyway.

机床附有电磁自动抬刀的刀架和刀杆。刀架用天外插削，刀杆用于内插削和插键槽。

18. hinged toolholder

活节刀夹

19. straight toolholder

直刀架

20. A comparatively advanced induction-type power supply has been developed to solve the critical problem that hindered this toolholder from being put into practical use.

研制了较先进的感应式电源,解决了供电方式这一阻碍测力刀柄推向实用化的关键问题。

21. Disposable toolholder bits

舍弃式刀头

22. In this toolholder,a thin-wall cylinder serves as the elastic element of its sensor and the cutting force signal is measured by a radio telemetric method.

这种刀柄以薄壁圆筒作为传感器的弹性元件;切削力信号的测量采用无线电遥测的方法;

23. Keywords Telemetric Toolholder Thin-Wall Cylinder Induction-Type Power Supply;

遥测刀柄;薄壁圆筒;感应供电;

24. This paper focus on simulating the KM toolholder taper interface positioning under different clamping force by using Finite-element Method.

针对KM刀柄锥面定位在不同夹紧力下进行有限元模拟,得到径向位移、接触应力、锥面间隙结果。

25. Performance Comparing of Hydraulic Expansion Toolholder, Polygonal Clamping Toolholder and Heat Shrinking Toolholder

静压膨胀式刀柄、应力锁紧式刀柄和热装式刀柄的性能比较