weld

weld

1. Four wheel smake it stable, and the two pulling boards can be discretionarily placed to weld.

5、小车四轮驱动，行走平稳，两拖板六自由度可实现任意焊接方式。

2. Frequency ERW pipe weld heat treatment to achieve the basic performance level of the base metal, and some even beyond.

ERW焊管焊缝中频热处理后各项性能也基本达到了母材的水平，部分甚至超越。

3. The corrosion resistances of fusion zone and weld decay zone have all decreased after GTAW and LBW process.

GTAW焊件在焊道及焊接衰化区的腐蚀情形会随著时间增加而加深。

4. Illumination of PLC panel and weld area and operation desk.

PLC柜,焊缝区及操作台的照明

5. PLC sequence panel including program software and weld programming terminal.

PLC程序控制柜,包括程序软件和焊缝程序终端。

6. FXD will not weld mild steel to steel because of the absence of free carbon in the preheat flame.

|| 因为缺少自由碳，FXD将不能进行火焰加热的钢与钢的焊接。

7. Inner hole weld" was a new process for the adjacent of tube to tube-sheet of pressure vessels.

“内孔焊”工艺是压力容器中管与管板连接所采用的一种新兴工艺。

8. Don't drill or weld on tube, coupler and plank frame.

不可以在架杆、扣件和踏脚板框架上打孔、电焊；

9. Don’t weld on training wheels.

不要固定培训工具。

10. Die Weld ist zehr Klein, die Weld ist zehr Klein.

世界其实很小，世界其实很小。

11. An approach is proposed that this deviation can be obtained by using the weld pool image centroid and a Kalman filter.

为此提出一种利用熔池图像质心和卡尔曼滤波来间接获取电弧与焊缝偏差的方法。

12. These should provide the reference for the investig ation of intelligentize weld control system.

为焊接智能控制系统的研究提供参考依据。

13. Mainly used in coating the weld joint of buried steel pipeline and insulated pipeline.

主要用于埋地钢质管道现场焊接补口和保温管线现场补口；

14. They also look for potential molding defects, such as gas entrapment, weld lines, shorts and sinks.

也可以看出潜在的模塑缺陷如气体夹陷、熔接线、缺胶和凹陷等。

15. This paper also introduces some laser weld equipment and weld process,performance of WTB and its application.

介绍了激光焊接的设备与工艺、焊接钢板的性能与应用。

16. Introduced here is the advanced flux cored down weld technology.

介绍了药芯焊丝自保护下向焊技术。

17. They weld the pieces of a broken axle .

他们焊接断了的车轴。

18. It is possible that he will use laser to weld the alloys.

他将用激光焊接合金，那是可能的。

19. His job is to weld parts together.

他的工作是焊接零件。

20. Weld whose heat resource is the laser, also owns the advantage such as low heat input and small heat deform.

以激光为热源的焊接同样也可以得到低热输入、变形量极少的效果。

21. After weld repairs, however, the overall quality and reliability of a cast valve is difficult to determine.

但是，在焊补后，铸件阀门的整体质量和可靠性就变得难于保证。

22. Steels in this group are more expensive as well as more difficult to machine and weld than low carbon steels.

低碳钢适用于以下情况：工具机身，把手，模座及其它不要求强度和耐磨性的类似情况。

23. It takes only two to four irradiations to inspect a sealing head weld by using the technology.

使用这种方法，一般只需两到四次透照就能完成封头焊缝的探伤。

24. The weld nugget had a dynamic recrystallized,fine isometric crystal structure.

其中,焊核为明显的再结晶等轴晶粒,晶粒明显细化;

25. Excellent gas cutting property and weld ability.

具有优异的焊接性能和切割性能。

26. Constant current output characteristics,deep melting penetration,even w-elding pool,and excellent weld.

具有恒流输出特征，熔透深，熔池均匀，焊缝成形良好。

27. The IWM travels inside the pipe.After completing a weld, the unit moves down the pipe to the next weld.

内焊机能在管子内部行走，在完成一条焊缝后，装置将沿着管子移动并靠近下一条焊缝。

28. It illustrated the importance and the bright prospect of the application of the automatic weld seam tracking in EBW.

分析了其组成、原理及其在实际生产中的应用,阐述了焊缝自动跟踪技术在电子束焊接中的重要性及其应用前景。

29. The weld Techniques of Aliform-Aluminium radiators very sensitive to the small variety of the parameter.

刚性太小时，稳定性欠佳，热胀引起的应力迫使夹具产生内部相对移动而使产品变形。

30. The maximum value of gapwise-averaged birefringence along the weld line occurred at a small distance from the obstacle.

制品最大双折射值出现在嵌件后一定距离处。

31. The halides of MnCl_2, CdCl_2, ZnF_2 and NaF reduce weld penetration as well as width.

卤化物MnCl_2,CdCl_2,ZnF_2,NaF都使熔深减小的同时也减小熔宽。

32. A transversely stressed fillet weld can sustain higher loads than one stressed longitudinally.

受横向应力的角焊缝比受纵向应力的角焊缝承受能力强。

33. Only firm action by the government can weld the nation together to face the troubles ahead.

只有政府的坚决行动才能使国家紧密地团结在一起，共同对付面临的困难。

34. Weld three-point, two point, single point, transom, cross - transom and special angle.

可实现四位、三位、二位、单点、中梃、十字梃、异型角焊接，四个 机头可同时工作，也可分别组合或单机单独工作。

35. Surface thermal spray weld process with alloy powder is a new technology of surface protecting and hardening.

合金粉末表面热喷焊技术是一种新的表面防护和强化工艺。

36. Install back coil pipe and collect box，after orientating，weld the connection together according to the drawings.

回装盘管及联箱，定位后现场焊接盘管与联箱的接口处，形式按船供图纸。

37. Hence lack of fusion and slag would exist at the weld root and create a large initial crack condition.

因而未熔透及夹渣存在于焊缝棍部，并造成大的初始裂纹条件。

38. The IIW [21] guidelines have been used to determine the weld detail categories (DC).

国际焊接学会的指导方针已经用于决定焊接详细分类。

39. A satisfied weld appearance was obtained under the optimized process parameters.The surface of observ...

在合理的工艺参数下,可获得表面光滑、无堆高和无变形等缺陷的焊缝。

40. No spalled paint exists at the plug weld and for a short distance each side of the plug weld s.

在塞焊焊缝处及塞焊周围距离内无细漆碎屑存在。

41. Weld up one support for the turbocharger.

在增压器焊上一根支撑。

42. Different forms of droplet transfer can be obtained, with spatters reduced and weld formation controllable.

在文中，对焊接工艺特点进行了研究。

43. The paper has analyzed the content about image processing in the weld seam tracking system.

在此对焊缝自动跟踪系统中有关图像处理方面的内容作了一些分析。

44. You must weld and grind this area before painting.

在油漆之前你必须把这个地方电焊修补、磨好。

45. A cavity is made on both sides of weld bead.

在焊道表面两侧作一空腔。

46. Before applying heat for a weld, the plates should be clamped together.

在用热进行焊接之前，必须把金属板紧紧地夹在一起。

47. It take speed and skill to weld steel at this heat.

在这样的温度焊钢需要速度和技术。

48. It takes speed to weld steel at this heat.

在这样的高温下熔接钢铁需要快速。

49. The maximal ratio of hybrid/MAG weld penetration is 1.5 and the lowest YAG laser power that augments MAG arc is 73 W.

复合与MAG焊缝熔深比最大达1.5，YAG激光增强MAG电弧的最小激光功率为73 W；

50. How do I weld stainless steel?

如何焊接不锈钢?

51. With Cold Jet, complete weld lines can be cleaned in 25 minutes.

如果使用Cold Jet,彻底清洁焊缝可在25分钟之内完成。

52. Assist the Engineering Department in producing Weld Maps if necessary.

如需要，协助工程部准备焊接图.

53. In the experiment, two tungsten electrodes set on both sides of weld pool provide transverse current to the pool.

实验通过布置在熔池两侧并随激光同步运动的钨电极向熔池中提供横向电流。

54. Review the Weld inspection repts f each project rectify any possible documentation errs.

审查焊接检验报告,修改文件上可能的错误.

55. Review the Weld inspection reports for each project and rectify any possible documentation errors.

审查焊接检验报告,修改文件上可能的错误。

56. Bolted bonnet with seal weld.

密封焊接的螺栓阀帽。

57. Dye penetrant examination of the completed weld.

对已完成的焊缝进行着色渗透检测。

58. The cause of the whirlpool of different metal in weld process and its removing method were showed clearly.

对异质金属焊接时出现的旋流,指出了成因及消除方法。

59. Result of testing for the fuzzy reasoning model shows,this way can be good used for weld defects calssification.

对模型进行试验测试,结果表明,该方法能够较好地对缺陷进行分类识别。

60. It utilizes X-ray to make benchmark lead wire image simultaneously with the weld seam in computer.

射线使用于传递同步跟踪信息的基准铅丝与焊缝同时成像于计算机中。

61. Workers are using electric welders to weld cracked steel.

工人正在用电焊机把断裂的钢筋焊结在一起。

62. Code for visual inspection and acceptance of site weld of engineering.

工程建设施工现场焊接目视检验规范。

63. A mininal error results in weld divergence.

差之毫厘，谬以千里。

64. CHANGZHOU WULIIAN ELECTRIC WELD AND SKIVE EQUIPMENT CO., LTD.

常州市武联电气焊割设备有限公司。

65. The distribution of residual stress of weld joints is analyzed.

并分析了焊接接头残余应力的分布规律。

66. Abroad using for induction cooker surge circuit and UPS power and high frequency turn weld machine.

广泛用于电磁炉震荡电路,UPS电源,高频逆转变焊机等。

67. And the draws of the stress, the whole life and the spot weld life of the crossmember are got after the analysis.

应用有限元分析法对副车架的疲劳台架试验进行强度和疲劳分析,得到副车架的应力分布图、副车架本体寿命云图和焊点寿命云图。

68. The effect of graphite morphologies on the crackingtendency of cast iron weld was studied with method.

应用本试验方法测定了石墨形态对铸铁焊缝裂纹倾向的影响。

69. Should be able to interpret weld X-rays and other common non-destructive test results.

应能看懂焊接X光和其他普通无损探伤检测结果。

70. The test is completed when unbuttoning commences without a fracture in the weld.

当开始解扣而焊接处却没有裂缝的时候,测试完成了。

71. Care must be taken to ensure that the surfaces are thoroughly clean first, for dirt will weaken the weld.

必须注意，首先要保证焊接头表面十分清洁，因为污物会减弱焊缝的强度。

72. Quick: Don't need to weld and galvanize, the setting time is 3 times quicker than the flange connect fitting.

快速不需焊接和再镀锌，安装速度比法兰连接管件快3倍以上。

73. Our botanists try to find out where useful weld plants grow .

我们的植物工作者们设法找到有用的野生植物生长的地方。

74. I would use a cohesive glue to weld the tubes to each other.

我会用粘胶把这些电子管粘起来。

75. I have suggested TSM buy the weld nut from USA(just like the cap nuts) to save time in finding a repair.

我已经建议TSM从美国采购焊接螺母（与这种螺帽很类似）以节省修理时间。

76. All cracks were detected in regions where such manually made weld passes existed.

所以检查到的裂纹都位于有手工焊缝存在的区域。

77. Remove all weld splatter and burrs.

所有焊缝必须焊透.

78. All weld build-up or buttering shall be 100 % examined by MT, followed by RT or UT.

所有补焊或对接焊应先进行100%磁粉检测，接着作100%射线或超声检测。

79. Weld abandoned tools onto the wheel.

把废弃的工具焊接上车轮。

80. Weld a bunch of untrained recruits into an efficient fighting force.

把未经训练的一群新兵组织成有战斗力的部队。